kemet emc filters 1 flld3 p v high current 3 - phase emc filter november 2015 overview the three phase filter series is intended to be used in energy conversion inverter systems (e.g. photo voltaic and wind power), between the inverter and the line or in motor drive systems. the filters are optimized for geometry and power loss. technical specifications rated voltage 520 va c rated frequency 50 - 60 hz rated current 2 50 C 2500 a leakage current < 5 ma *) rated temperature 50 c temperature range - 40c to +100c climate category 40/100/21 voltage test p - > p 225 0 vdc (520 vac) p - > e 3 0 00 vdc (520 vac) the flld3 p v series is designed according to iec/en 60939 and ul 1283. *) maximum leakage current under normal operating conditions. if two phases are interrupted, leakage current can be much higher. filters without y - capacitors have no leakage current. v = 520vac x = 520vac without y - capacitors typical insertion loss 25 0 to 1000 a 1600 and 2500 a part number rated current @ 50c (a) power loss @ 25c/50hz (w) weight (kg) flld3250ap - i1 250 1 5 7 flld3320ap - i1 320 15 10 flld3400ap - i1 400 25 10 flld3600ap - i1 600 40 11 flld3800ap - i1 800 50 17 flld31k0ap - i1 1000 75 17 flld31k6ap - i1 1600 130 26 flld32k5ap - i1 2500 23 0 55 0.01 0.1 1 10 100 frequency (mhz) 10 20 30 40 50 60 70 80 90 100 0 attenuation (db) sym asym asym no y-cap 0.01 0.1 1 10 100 frequency (mhz) 10 20 30 40 50 60 70 80 90 100 0 attenuation (db) sym asym asym no y-cap
kemet emc filters 2 flld3 p v high current 3 - phase emc filter november 2015 mechanical dimensions part number dimensions in mm l w h l1 w1 w2 u x y z i j k n m flld3250apvi1 300 180 125 120 205 230 55 5 20 45 15 9 m10 flld3320apvi1 300 210 115 120 235 260 60 6 25 45 15 10.5 m12 flld3400apvi1 300 210 115 120 235 260 60 6 25 45 15 10.5 m12 flld3600apvi1 300 210 135 120 235 260 60 8 25 45 15 10.5 m12 flld3800apvi1 350 230 170 145 255 280 60 8 40 55 20 14 m12 flld31k0apvi1 350 230 170 145 255 280 60 8 40 55 20 14 m12 flld31k6apvi1 400 250 16 0 170 275 300 60 10 60 95 17 26 26 14 m12 flld32k5apvi1 450 300 22 0 20 0 330 370 100 15 8 0 11 0 20 35 35 14 m12 tolerances, if not stated, according to: iso 2768 - m legal disclaimer notice all product specifications, statements, information and data (collectively, the information) are subject to change without notice. all information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute C and we specifically disclaim C any warranty concerning suitabil ity for a specific customer application or use. this information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their applications. any technical advice inferred from this infor mation or otherwise provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained. although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as inst allation of protective circuitry or redundancies) in order to ensure that failure of an electrical component does not result in a risk of personal injury or property damage. alt hough all product - related warnings, cautions and notes must be observed, the c ustomer should not assume that all safety measures are indicated or that other measures may not required l w h u y x z w1 w2 z l1 l1 ?12 (x6) u k j i i ? n 250 to 1000 a m k j i ? n 1600 a 2500 a ? n
|
